- Degree in mechanical, electrical, automotive or mechatronics engineering, or equivalent.
- At least 5 years in vehicle test, validation or prototype engineering at an OEM or tier one, including a program through start of production
- Hands-on execution of vehicle, system and component DVP&R with requirement-to-test traceability.
Role Type
Description
About Niivo:
At Niivo we are passionate about powering the next chapter of e-mobility and energy in global emerging markets through intelligent solutions. Our name says it: Niivo means moving together towards a better, more sustainable future.
Founded by a team with deep experience in electric vehicles and energy, our mission is to inspire and enable the adoption at scale of electric mobility and renewable energy in Global Emerging Markets, starting with Africa and LATAM. We believe in the opportunity to move the world forward through clean energy, connected mobility and shared progress. Our products, technology and services are one integrated ecosystem — Vehicles + Charging + Energy / Asset /Payment Management— that are low cost by design, obsessively fitted to its market, and software-defined and connected. Every Niivo product is deeply thoughtful, vertically integrated, built from first principles, and made to work at scale.
The role:
Based in India, you will be Niivo’s test engineer at the point where our parts and vehicles are made. You make sure that every part, system and vehicle is tested the way it was specified, that sign-off is backed by evidence, and that what reaches our customers has been proven. After launch, you carry the same discipline into our software-defined vehicles in service: over-the-air releases, early-life issues and quality escapes traced back to the factory.
You will work across several vehicle programs at different stages at once, so the test methods, rigs and data you build must carry from one program to the next.
Responsibilities & accountabilities:
- Supplier test assurance: be Niivo’s eyes and ears at suppliers across India. Witness and audit supplier-side testing, confirm that set-up, samples, instrumentation and procedure match the agreed specification, and challenge results where method or evidence falls short.
- DVP&R execution: own execution of the vehicle, system and component DVP&R across Niivo’s vehicle programs, internally, at suppliers and at external labs, with requirement-to-test traceability for every sample.
- Sign-off integrity: close a test only when the sample state is traceable, the method follows the procedure and the acceptance criteria are met. Report deviations plainly, including when they put a program gate at risk.
- Type approval readiness: plan and run development testing so it anticipates type approval requirements across all target markets, pre-test against the regulations, and witness certification testing at approved labs.
- Production line test: define the test content, limits and pass/fail criteria for end-of-line and in-process testing, and verify during line set-up and run-at-rate that each test detects the failure modes found in validation.
- OTA release verification: run vehicle-level regression testing on every over-the-air release ahead of fleet deployment, complementing bench and HIL testing, and report release readiness to software and controls.
- Early-life issue support: support investigation of escalated early-life field issues, using test reproduction and failure analysis of returned parts to establish root cause.
- Factory and supplier quality: be Niivo’s on-site presence for quality issues traced to the factory or a supplier, providing the test evidence for containment and 8D, and verifying that corrective actions hold.
- Test capability: build and own Niivo’s test capability across locations: methods, rigs, equipment, lab partners and test data, built for reuse on future vehicles and products.
Person requirements:
- Degree in mechanical, electrical, automotive or mechatronics engineering, or equivalent.
- 5+ years in vehicle test, validation or prototype engineering at an OEM or tier one, with at least one program through start of production.
- Hands-on DVP&R execution and working knowledge of national and international vehicle and battery standards, including preparation for type approval in more than one market.
- Automotive quality tools: APQP, PPAP, FMEA, MSA and 8D; able to read GD&T drawings and CMM reports.
- Instrumentation, data acquisition and CAN tools (e.g. Vector CANalyzer), including UDS diagnostics and ECU flashing.
- Safe working practice on EV battery systems; experience defining end-of-line or in-process test.
- Python or similar for test automation and data analysis; exposure to OTA release testing or hardware-in-the-loop is an advantage.
- Track record of test methods and rigs that were reused across programs rather than rebuilt for each one.
- Willing to challenge suppliers and internal teams when evidence does not support sign-off.
- Works independently in a small team across UK, Africa and the Americas time zones, and writes reports a supplier can act on.
- Based in or willing to relocate to Hyderabad, with frequent travel to suppliers across India and occasional international travel.
Before you apply, please read how we handle your information in our privacy notice: https://www.niivo.com/privacy
Australia
New Zealand
United Kingdom
Canada
Singapore
Malaysia





